Gavin scooter parts In case George Irvine does not have in stock O-rings ------- Parker number inner diameter x width port plug...............................2-110.............9,19 x 2,62 mm motor...................................2-248...........120,24 x 3,53 mm motor and motor compartment.............2-252...........132,94 x 3,53 mm motor compartment.......................2-256...........145,64 x 3,53 mm body....................................2-375...........240,67 x 5,33 mm Battery pack connectors ----------------------- These are gold connectors from Superior Electric. Allied Electronics part# o Supercon PS25GB (black) 645-0027 o Supercon PS25GR (red) 645-0034 These are expensive and you migth find GI to be cheaper than Allied with shipping and handling. Charging plugs -------------- These are Molex type 1545 plugs. o Charger/burn tester: * House: Molex part# 03-09-2022 * Terminal: Molex part# 02-09-2103 Set of house and terminal: Radio Shack part# 274-151 o Battery pack: * House: Molex part# 03-09-1022 * Terminal: Molex part# 02-09-1104 Set of house and terminal: Radio Shack part# 274-154 A complete set of plugs and terminals: Radio Shack part# 274-222 o Charger side drawings: * Housing: http://www.molex.com/pdm_docs/sd/003092021_sd.pdf * Terminal: http://www.molex.com/pdm_docs/sd/002098109_sd.pdf o Battery side drawings: * Housing: http://www.molex.com/pdm_docs/sd/003091027_sd.pdf * Terminal: http://www.molex.com/pdm_docs/sd/039000295_sd.pdf Motor cable terminal -------------------- 3M Highland Female Disconnect FD14-250L or equivalent ¹ Reed switch ----------- For older type (PVC): Radio Shack part# 49-496 Relay alternatives ------------------ 1) Potter & Blumfield/Tyco: T90S1D12-24 CLASS F, FORM A (SPST-NO) -- original on my 1999 Gavin 2) Magnecraft & Strutters-Dunn: W90S1D12-24 3) American Zettler: AZ2150(or 2151)-1A-24DE 4) Omron: G8P-1A4-DC24 Any closed (epoxy) relay for 24V with same pin config should work. Motor ballbearing alternatives ------------------------------ 1) NMB, IR-14380 ² 2) KSK, 7R 6 ² 3) NTN, R6LLU/2A ¹ Abra AS in Trondheim, Norway has some of these in stock. Shaft seal alternatives --------------------------------------- o PAC-SEAL Flowserve 10304 PAC Shaft Seals o AG-RAIN 465-4868 ³ o AURORA PENTAIR 712-0901-753712-0931-753712-1001-753 ³ o CONTINENTAL MACHINE 2930 ³ Screws ------ * On end of shaft: #10-32 x 3/8" flat head * For clutch assembly: #8-32 phillips pan head * At end of pitch adjustment knob: #6 x 3/4" phillips flat head stainless steel Latches ------- Nielson Sessions * Catch: HC83314SS (Stainless) * Strike: HS83314SS (Stainless) Misc ---- If paint start bubbling on the cone: sand(blast), use outboard engine primer and paint. DO NOT MESS WITH SEALING SURFACES! Alu-clutches not from George (AJ clutches) use #8-32 hex pan head screws. You need a 9/64 hex key for this. Replace hex screws with phillips if you can source them. A 9/64 hex key is not commonly found in the typical smaller tool stores in Europe. Addresses --------- Abra AS - http://www.abraas.no Superior Electric - http://www.superioreletric.com Allied Electronics - http://www.alliedelec.com Radio Shack - http://www.radioshack.com Sources ------- Mostly compiled from info on quest list, gavinscooter list and suppliers/manufacturers. ¹ From Sigurd Bowitz ² From Jan Arild Aaserud ³ Not confirmed to be correct -- Olaf Trygve Berglihn